Your Cart

Flight Controller Accesories

SPECIFICATION Connector: Micro USB / USBLength: 1M Weight: 27gColor: Black / GoldCoper Wire: 35/0.8*2C+10/0.8*2CCable Outer diameter: ~4mm..
Brand: speedy Bee Model: Speedy Bee Bluetooth-USB Adapter
Description Have more stable and faster transmission performance Low-Power Bluetooth Solution Standalone Transmission Control Chip 1KB Data  Cache Expansion   NO CONFIGURATION REQUIR..
Model: Optical Flow Sensor for APM2.52 APM2.6 Flight Controller
Optical Flow Sensor for APM2.52 APM2.6 Flight Controller   Note: Please open the lens before use, remove the protective film Cannot focus closer than 30cm - Can Adjust Focal length to achieve better result..
Model: minim OSD with case - APM pre flashed
MinimOSD Rev. 1.1 OSD Description: On-Screen Display Ardupilot Mega MinimOSD Rev. 1.1 OSD diy drones APM2 APM2.5 APM2.6 APM has an companion OSD board called MinimOSD. It reads all the MAVLink data in the APM telemetry stream and overlays it on the video stream if you're using an on-board camera and..
Model: Micro USB OTG on the go cable
With this cable and a compatable android phone you can adjust your flight controllers settings and pids - even flash new firmware. Leave your laptop at home a grab an OTG cable
Model: FTDI 5V Micro USB Turn To TTL MWC CP2104 Debugger Programming Un
Description: Item name: CP2104 debugger Chip: CP2104  Weight: 0.9g   Package included: 1 x CP2104 debugger 1 x pin set..
Model: Dampened flight controller mounting 35mm - naze/cc3d/flip32
Rather than using the ridgid flight controller standoffs try one of these on your next build - sits a little higher but can cut any vibrations from poorly balanced props or unbalanced motors.  ..
Model: Bluetooth module
This small bluetooth module allows you to connect wirelessly to your  flight controller from your android phone / tablet or your pc   • Read and Write PID • Setting switch adjustment for AUX1 and AUX2 • Monitor receiver signal and FC output signal • Monitor all sensor..
Model: Arduino nano v3 (silabs esc programmer blheli)
100% New,for Arduino-Compatible Board Fully Compatible for Arduino Nano V3.0 ATmega328P-AU ATmega328 Microcontroller Bootloader installed, ready to upload sketches for Arduino software Microcontroller ATmega328P-AU  Operating Voltage 5V  Input Voltage (recommended) 7V-12V  Inpu..
Model: APM Led indicator board
Description: - The LED indicator is for APM/MegaPirate. There are four 3W led White/Red/Green/Bule on the board, and it can be setting light up method in Mission Planner. - The LED Indicator supported 5~30V input. Specification: - Dimension: 57 x 20 x 8mm - Weight: 10g..
Model: Ultrasonic Module HY-SR04 Distance Sensor (Sonar)
Ultrasonic sensor for use in Arduino projects to measure distance, can be used with Multiwii boards / megapirate / Arducopter. Really easy to add to the Naze32 in baseflight and cleanflight - great for Carpark racing : ) Works better indoors or on flat surfaces - grass can reflect with angles great..
Model: ST-Link STM8/STM32 v2 Programmer & Emulator
Can use this tool to program the Eachine Pro 5.8 to add on the Achilliez firmware Explore new microcontroller worlds with an ST-Link Programmer & Emulator / Debugging dongle. This little USB stick contains a microcontroller with the code for ST's classic programmer/emulator for STM8 and STM..
Model: SpeedyBee Bluetooth-UART Adapter
SPECIFICATIONSParameter◇Output Power: 0dBm◇Receiver Sensitivity: -94 dBm◇External Interfaces: BROADCAST SWITCH, TX, RX, 3~5V DC Input, GND◇Transmission rate: Bidirectional 1K/S◇Bluetooth Protocol: Bluetooth Specification V4.0 BLE◇Transmission distance: 30m◇Frequency range: 2400 MHZ - 2483.5MHZ(2.4G ..
Brand: DYS Model: Flight controller grommets
Simple grommets to completely isolate your flight controller from the frame. require most flight controller holes to be drilled out to 4mm to seat the grommets. check that your flight controller can be drilled out to accommodate - not all boards can be! 4 grommets included in the kit..
Model: Buzzer (for flight controller)
Buzzer for the Naze / Lazybee / KK2 / Flip Great to get audible feedback from the flight controller and also low battery alarm. If you are flying a mini an essential piece of hardware to help you find a down model. 5cm - jst    ..
Model: USB ASP ISP AVR Programming Device for ATMEL proccessors
These AVR programmers are based on Thomas Fischl's USBasp design and connect to your computer's USB port. Not only are they quite compact (70x20mm), but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done in firmware. Being an O..
Showing 1 to 16 of 20 (2 Pages)