Glide 5 – Constructed of Premium Materials
This is the updated version of the popular Glide frame fabricated in high quality
materials. This product is quality controlled by the designer himself, KababFPV.
Good quality drivers or otherwise drivers that will not strip or deform such as
those made by MIP are STRONGLY encouraged. Some of the arm mounting
holes may be a bit tight. You may need to thread a screw through the hole
before mounting it or run a 3mm drill bit through it. Everyone loves tight
tolerances but the manufacturer is a bit overzealous about it. It’s being managed
from batch to batch.
The Glide is manufactured with 2mm body plates and 5mm arms. The Glide Lite
uses 1.5mm body plates and 4.5mm arms while the Hammer version uses 3mm
body plates and 6mm arms. The Glide is ~99g while the lite is ~85 and the
Hammer is ~130g. The lite version is recommended for those looking for a
lighter build with sub 29g motors and smaller electronics. The Hammer version
is intended to be a super basher but it’s pretty extreme. The base Glide is
recommended for the vast majority of builds.
● Fits 5.1” props
● Motor mount pattern: 16×16 and 19×19
● Frame weight fully built with FPV cam mount: ~99g, ~86g lite, ~130g
● Premium materials
● True X layout with option of dead cat arms
● One central 30×30/20×20 mounting platform flanked by two 20×20
platforms all accessible at all times with no interference.
● No stack screws touch any arm parts. No arm/stack integration.
● Two screws per independent arm with bracing against other arms. Easy
swaps and secure fit.
● 23mm standoffs (fits vista with low cam tilt, 25mm recommended for DJI
● Motor bumpers on arms really do save motors from damage.
● GoPro mount platform compatible with legacy FlosStyle and Flowride
● 12.9 hardness steel screws and steel press-nuts because ain't nobody
got time for stripped aluminum. (switched back to black because it’s
● Micro and Nano sized FPV camera spacing (20mm wide or narrower)
● Dead Cat arms available to be purchased separate
Please thread your central stack screws before assembling the arm and lower
plate complex. Also, carbon compresses over time. The arm/lower plate complex
is very tight the first time you put the frame together. each successive time it will
not be that tight.
The Glide Floss is built to work for you. While it comes in nicer carbon with pretty
finishes, its focus is convenience and compatibility rather than aesthetics. The
option of dead cat arms is directed at those needing a workhorse for FPV
videography and absolutely must get their props out of view with low GoPro tilt.
The arms are also easy to swap so you can go back and forth. This design
comes from the legacy of Hyperlite and Floss frames with optimizations over all
freestyle frames in the series before it. If you’re running a Flowride or FlosStyle,
we know you love them but overall this design is better balanced, easier to build
and maintain, stronger and comes in better carbon.
Weight adds up quickly and is enemy #1 for flight performance. You don't really
need that giant Vtx antenna mount or those thicc TPU shoes. The 20×20
mounting platform in front is primarily intended for your flight controller. This is
due to the heaps of various types of noise radiating from your ESC, power lines,
vtx and most importantly, the Crossfire receiver. Telemetry left on with Crossfire
will disturb your OSD chip and camera. It's recommended that your Crossfire Rx
be moved to the rear while the camera and FC stay up front. The first time you
put this frame together it will be very tight. It will seem like the holes are off,
they're not. Carbon compresses over time and this design will compress to
normal rather than loose which causes arm wiggle. If your frame doesn't feel
rigid after a while, please tighten your screws. They too come loose over time.
● Recommend 650g AUW or below for 5". Sub 610g AUW is ideal.
● 2207, 2306, 2208, 2306.5, 2307, 2407, 2305 motors in ~1800kv 6S or
● Recommend motor weight under 35g
● Sub 200g battery 4S-6S
● Sub 4.3g 5" or 5.1" prop
● Any 20×20 FC
● WaFl premade cap
● Please use blue loctite for inner arm mount screws…unless you're lazy
like us. Then just know that they may come loose over many flights.
Further recommendations about
Glide floss is not really the best floss for your teeth, it just fit the naming scheme
well. It's made of a very slippery material that may fit between teeth easily but
also slips over plaque easily. While it may be the only floss people with braces
can use effectively, Reach Dentotape is far superior floss. It's double wide and
braided so it will gently scrub the sides of your teeth and gums clean. Please
floss at least once a day and stay away from products containing high fructose